IK Multimedia iRig Acoustic Stage Advanced Digital Mic System for Acoustic Guitar #63529

This unit is pre-loved but in great condition with minor wear.

The combination of its advanced MEMS microphone and hi-quality preamp and DSP processing unit provides — for the first time ever — a break-through solution that offers hi-quality natural sound, advanced features, ease of installation and a convenience never seen before.

Until now, getting your acoustic to sound like it does in the studio when playing on stage has been a difficult, if not impossible, task. Playing an acoustic on stage typically falls into two scenarios: using the onboard piezo or magnetic pickup system to project a fractional representation of your acoustic’s natural warm tone, or sitting stationary on stage with microphones in “the sweet spot” on your acoustic, dramatically limiting your ability to move.

With iRig Acoustic Stage, you no longer have to sacrifice great acoustic tone when playing live. iRig Acoustic Stage gives you the best of both worlds — the beautiful, rich sound of your acoustic guitar as if it were mic’d up in the studio AND the freedom to move around without compromising your sound. Sound impossible? Read on…

iRig Acoustic Stage is a patented, revolutionary digital microphone system that makes your guitar sound exactly as if it was captured with a classic recording studio setup, giving you full rich studio-quality sound on the stage.

It’s a compact acoustic microphone and advanced digital preamplifier and processing unit that recreates a studio microphone set-up providing you with all of the true character and tonal nuance of your acoustic in live playing situations.

Simply clip the iRig Acoustic Stage’s microphone to the sound hole, attach it to the iRig Acoustic Stage pre-amplifier processor, then connect the preamp to your amplifier or mixer.

iRig Acoustic Stage also features a “Cancel Feedback” button that gets rids of annoying frequency feedback during performance.

Features

Advanced MEMS microphone clips on to sound hole
Preamp/DSP unit
Dramatically improves your live acoustic sound
1/4″ AUX input with volume for piezo, magnetic pickups or other onboard electronics
1/4″ Output with level control for amplifier or PA system
USB audio out for recording on a computer or mobile device
Cancel Feedback with multiple frequency feedback cancelling
6 tone presets
Personal instrument calibration
Works on any acoustic, acoustic electric or ukulele with round sound hole
Phase switch for optimizing dual source sound
Specifications

Microphone Type: MEMS
Polar Pattern: omnidirectional
Frequency Response: 30 Hz – 20 kHz, +/-3dB
Max SPL: 130dB SPL
Signal-to-Noise Ratio: 101 dBA
Maximum soundboard thickness: 4mm / 0.16″
Dedicated iRig Acoustic Microphone Input: 2.5mm / 3/32″ TS mono jack
AUX Instrument Input Connector: 6.3mm / 1/4″ TS mono jack
AUX Instrument Input Impedance: 1 MOhms
Analog Output Connector: 6.3mm / 1/4″ TS mono jack, line-level, low impedance
Analog Output Impedance: 50 Ohms (can drive long cables without any loss)
Digital Output Connector: micro-USB
AD and DA Resolution: 32-bit
Sampling Rate: 48 kHz
Interface Output: USB class compliant audio output via micro-USB port
Power: battery power (2xAA), USB bus power
Battery Life: approximatively 12 hours of continuous usage with alkaline batteries and 15 hours with rechargeable high quality Ni-MH AA cells (2000 mAh and up)
DSP/Interface size: 101mm/3.98″ x 72.3mm/2.85″ x 23mm/0.91″ (belt clip excluded)
DSP/Interface weight: 99g/3.49oz (batteries excluded)
Microphone size: 31.7mm/1.25″ x 32.2mm/1.27″ x 18.8mm/0.74″
Microphone weight: 20g/0.71oz
Microphone cable length: 150cm/59.1″

Compatibility

• iRig Acoustic Stage can be connected to any amplifier, mixer or PA system using a 6.3mm / 1/4″ TS mono jack cable.
• iRig Acoustic Stage can also be used as USB recording interface for Mac/PC, iOS, Android.